Shop
Piezo Plate 35mm
In stock
A piezoelectric transducer converts mechanical force into electrical output. This is made up of Quartz crystal which contains SiO2. Piezoelectric crystals are electrically neutral. The atoms inside the crystals in an unsymmetrical manner but their electric charges balanced.
PIR Motion Sensor
In stock
Features :
- Infrared Sensor with Control Circuit Board
- The Sensitivity and Holding Time are adjustable.
- Blockade time: 2.5s (Default)
- Sensitive Setting: Turn to Right, Distance Increases (About 7M); Turn to Left, Distance Reduce (About 3M)
- Time Setting: Turn to Right, Time Increases (About 200S); Turn to Left, Time Reduce (About 5S).
PIR MOTION SENSOR S221 – 220V
In stock
Installation
Shut off the power.
Loosen the screw on the bottom lid. open the wining hole, pass the wire of power, and load through the bottom lid.
Fix the bottom lid with an inflated screw on the selected position.
Connect the power and load wire into the connection-wire column.
Put the sensor on the bottom lid, twist the screw tightly then electrify it and test it.
Test
Turn the light-control knob clockwise to the maximum (SUN), turn the time knob anti-clockwise to the minimum. Switch on power, the controlled load should not work, under the no induction signal condition, the load should stop work within 5-30sec. Make it sense again 5-10sec later since the first is out, the load should work, the load should stop working within 5-20sec. Turn the LUX knob to minimum anti-clockwise, if you test it when the light control is more than 3LUXx, the induction load would not work after the load stops working. the load should work if you cover the detection window with an opaque object (towel etc). It would be regular the load stops to work within 5-15sec under no induction signal condition.
Pixhawk 2.4.8 Drone Flight Controller PX4 32 Bit Autopilot
In stock
The most common question asked by our community is “what is flight controller” and the answer is here The flight controller (aka FC) is the brain of the Drone(Quadcopter). It’s a circuit board with a range of sensors that detect movement of the drone, as well as user commands so Pixhawk 2.4.8 does. Using this data, it then controls the speed of the motors to make the craft move as instructed.
It Supports 8 RC channel with 4 serial port. Various user interfaces are available for programing, reviewing logs, even some apps for smartphones & tablets. It detects and configures all its peripherals automatically
Pixhawk 6C (Plastic Case)
In stock
The Pixhawk 6C is the latest update to the successful family of Pixhawk flight controllers, based on the Pixhawk FMUv 6C Open Standard and Connector Standard. It comes with PX4 Autopilot® pre-installed. Inside the Pixhawk 6C, you can find an STMicroelectronics based STM32H743, paired with sensor technology from Bosch & InvenSense, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications.
The Pixhawk 6C’s H7 microcontroller contains the Arm Cortex-M7 core running up to 480 MHz, has 2MB flash memory and 1MB RAM. Thanks to the updated processing power, developers can be more productive and efficient with their development work, allowing for complex algorithms and models. The FMUv6C open standard includes high-performance, low-noise IMUs on board, designed to be cost-effective while having IMU redundancy. A vibration isolation System to filter out high-frequency vibration and reduce noise to ensure accurate readings, allowing vehicles to reach better overall flight performances. The Pixhawk 6C is perfect for developers at corporate research labs, startups, academics (research, professors, students), and commercial applications.
Pixhawk 6C PM02
In stock
The Pixhawk 6C is the latest update to the successful family of Pixhawk flight controllers, based on the Pixhawk FMUv6C Open Standard and the Connector Standard. It comes with PX4 Autopilot pre-installed. Inside the Pixhawk 6C, you can find an STMicroelectronics based STM32H743, paired with sensor technology from Bosch® & InvenSense, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications.
The Pixhawk 6C’s H7 microcontroller contain the Arm Cortex-M7 core running up to 480 MHz, has 2MB flash memory and 1MB RAM.
PL2303 USB TO TTL
In stock
Features :
- Adopt imported controller PL2303HX, which can stabilize the flash with high speed
- 500mA self-recovery fuse for protection.
- Two data transmission indicator can monitor data transfer status in real time.
- Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power.
- The entire board is coated by the high quality transparent heat-shrinkable sleeve, making the PCB in insulation state from outside.
- so that the board won’t be burnt down by material shortcut.
- The electrostatic package ensures the board will not be damaged before use.
- Support WIN7 system.
PL2303 USB To UART (TTL) Communication Module V2, USB-A Connector
In stock
This is the PL2303 USB UART converter Board. This is a great little tool for embedded systems that require a serial connection to a computer. The board can simply attach to a USB-C bus and will appear as a standard COM port.
Planetary Gear DC motor – 10 RPM / 12V
In stock
If you are searching for a motor with very high torque then this Tauren Planetary Gear DC motor – 10 RPM / 12V will fulfill your specification demands. The Tauren Planetary Gear DC motor has the massive torque of 23 kg-cm at no load. The planetary geared motors are always well known for their low backlash and higher efficiency characteristic to meet the higher expectation.
As these Epicyclic Gear Train motors are very popular amongst our Robotics designer. So we must ensure them for the quality and performance of these motors.
PM2.5 Dust Sensor GP2Y1014AU0F
In stock
This PM2.5 GP2Y1010AU0F Dust Smoke Particle Sensor is an infrared emitting diode (IRED) and a phototransistor are diagonally arranged into this device. It detects the reflected light of dust in the air. Especially, it is effective to detect very fine particle like the cigarette smoke. In addition, it can distinguish smoke from house dust by the pulse pattern of the output voltage.
The module is mainly used for dust removal equipment alarm equipment, air purification equipment, dust robots, fire alarm, etc. industry equipment can detect smoke particles, pollen spores, and other particles.
PN532 NFC RFID Read / Write Module V3 Kit
In stock
The PN532 is a highly integrated transmission module for contactless communication at 13.56 MHz including microcontroller functionality based on an 80C51 core with 40 Kbytes of ROM and 1 Kbytes of RAM. The PN532 combines a modulation and demodulation concept completely integrated for different kinds of contactless communication methods and protocols at 13.56 MHz with an easy-to-use firmware for the different supported modes and the required host controller interfaces.
PNL119 – 12V DC Slim Siren
In stock
Features:
- Low energy consumption
- Low maintenance
- Absolute reliability
POWERGUARD (PG08T)
In stock
Measures
- Power (W)
- Power Factor (PF)
- Carbon Emission (CO2 in Kg)
- Total Used Time (MIN)
- Money (CU)
- Tariff (CU/KWh)
- Timer (DHH:MM)
- Frequency (Hz)
- Energy (KWh)
- TRMS Current (mA)
- TRMS Voltage (V)
Pre-Crimped Cables and SH1.0 Connectors Silicone 15cm Wire
In stock
PRO – MINI
In stock
Features :
- ATmega328 running at 16MHz with external resonator (0.5% tolerance).
- 100% Arduino compatible board.
- Max Output Current: 150mA.
- Over-current protected.
- Reverse polarity protected.
- 0.8mm Thin PCB.
- USB connection off-board.
- Supports auto-reset.
- Onboard Power and Status LEDs.
PROGRAMMABLE ROBOTIC MONSTER TRUCK 2-in-1 DO IT YOURSELF BLUETOOTH/MOBILE CONTROLLED ROBOT KIT
In stock
Kit Includes:
1. Chassis 2 mm & 1 mm Metal Parts – 10
2. 125 mm Dia Rubber Wheels – 4
3. 85 mm Dia Rubber Wheels -4
4. Long Hex Couplings – 4
5. Short Hex Couplings – 4
6. Jumper Wires
7. Arduino UNO – 1
8. Arduino UNO Cable – 1
9. Motor Driver – 1
10. Bluetooth Module – 1
11. M3x6 Allen Button Head Screws – 30
12. M4x10 Allen Button Head Screws – 35
13. Allen Keys – 2
14. Assembly Manual (Mechanical and Electronics) – 1
15. 300 RPM DC 12V Side Shaft Motors – 4
PROGRAMMER CLIP
In stock
SOP8 IC Programmer Test Clip with Welding Wire is perfect for reading or writing EEPROMs. This clip allows for in-circuit programming of SOP8 chips.
