Shop
1×1 Matrix Membrane keypad
In stock
1×1 Matrix Membrane Switch Keypad features a 1 button. This is a membrane keypad with no moving parts. A female 2-pin berg connector is required for interfacing it with your microcontroller circuits. A simple way to mount the keypad in a variety of applications, as it has an adhesive backing.
2 AND 3 CELLS LIPO BATTERY CHARGER
In stock
This is SKYRC E3 AC 2S / 3S Li-Po Battery Charger (V2) (Original), it takes 100-240V, good for any country in the world. There are no buttons on the charger, so simply wait for the chargers green lights to come on, which means the battery is ready. It takes about 1-1.5 hours to charge an 11.1V 2200mah Li-Po Battery Pack.
2 Meter GT2 Timing Belt + 2Pcs of GT2 pulley (20 teeth)
In stock
This is 2 Meter GT2 Timing Belt + 2Pcs of GT2 pulley (20 teeth).
The Pulley and The Timing Belt combo forms an integral part of the 3-D printer. These are used for the precision motion to print even the most intricate designs. GT2 Timing Belt Pulley is widely used in the 3d printer. GT2 Timing Belt pulley Specially design for NEMA 17 stepper motor used in 3d Printer.
2 Module 23A Touch Switchboard White/Black
In stock
Features:
- Control From Anywhere
- Works with Existing Wiring
2 Module Retrofit Device
In stock
Features:
- Make Existing Switches Smart
- Control From Anywhere
- Compatible with Manual Switches
- Works with Existing Wiring
2 Pin 3.81mm Pitch Pluggable Terminal Block
In stock
This terminal block is pluggable, which means that it can be easily inserted and removed from a corresponding socket without the need for any additional tools. It features a compact and durable design, with a molded plastic housing that provides protection and insulation to the internal components.
2 PIN TOP RELAY
In stock
Why are Protection Devices used in a Relay?
2 PIN WIRE CONNECTOR CNT
In stock
CH-2 Way Quick Push Type Lock Electric Wire Connectors Terminal (Pack of 5 Pcs)
2 WHEEL ROUND KIT
In stock
- Outline Size: 135 x 135 x 80mm
- The round acrylic plate diameter: 130mm
- Another acrylic plate size: 135 x 75mm
2-4S 20A x2 Dual Way Brushed ESC Speed Controller
In stock
Key Points of Mixed Control Debugging:
l First make sure the forward and backward motors are in the same direction. (If a motor is turning incorrectly, exchange the +-stage wires behind the motor)
l Then adjust the direction, if it is not as expected, the remote control may be reversed, set it back
The Dual-mix ESC Has the Following Modes:
l Mixed control mode (both throttle / steering mode): 2 or 3 channels (2 channels are recommended because 2 channels automatically return to center) to control the throttle, 1 channel (or 4 channels) to control speed difference steering, throttle ratio 100%, steering ratio 100%, steering priority. Suitable for: tank (in this mode, gun control can play tanks), 4-wheel drive trolley (apm can be installed)
l Two-way independent: it is equivalent to two independent ESCs (if you want to simulate a real tank, the white three wires on the input end are connected to the receiver throttle (3 channels), and the yellow single wire is connected to the receiver 2 channels)
l Two-way synchronization: In mixed control mode, do not connect a single yellow wire, so that the two-way motor output is consistent
2.4G 150mm Receiver Antenna regular
In stock
This is a 2.4G 150mm Receiver Antenna regular version IPEX1. This Connector is used to connect the receiver. the 2.4G control made it unique because it can connect most of the Receivers. The cable length of the connector is 150 mm and This connector has RF113 silver plated wire for that reason this it is good precision machining also it has low loss and high sensitivity.
2.4GHz 3.2dBi RP-SMA female Omni Antenna for WiFi
In stock
This 2.4GHz 3.2dBi RP-SMA female Omni antenna is intended for use for all 2.4GHz applications. The antenna is fitted with an RP-SMA female connector and a blade, made of a flexible material that can be rotated 360 degrees. Suitable for telemetry and WIFI transmissions on lightweight unmanned platforms.
This 2.4GHz 3.2dBi Gain indoor antenna provides high gain and provides tilt and swivel functions for full flexibility.
2.4GHz 5dBi Omni Wi-Fi Booster SMA Male Antenna
In stock
2.4GHz 5dBi Omni WiFi Booster SMA Male Antenna for Wireless Router. It is Extremely compact low profile housing for minimum visibility and maximum overhead clearance.
2.4GHz NRF24L01+PA+LNA SMA Wireless Transceiver Antenna
In stock
The NRF24L01 module is the latest in RF modules. This module uses the 2.4GHz transceiver from Nordic Semiconductor, the NRF24L01+. This transceiver IC operates in the 2.4GHz band and has many new features! Take all the coolness of the 2.4GHz NRF24L01+PA+LNA SMA Wireless Transceiver Antenna and add some extra pipelines, buffers, and an auto-retransmit feature – very nice!
2.4GHz NRF24L01+PA+LNA SMA Wireless Transceiver Antenna
In stock
This transceiver IC operates in the 2.4GHz band and has many new features! Take all the coolness of the 2.4GHz NRF24L01+PA+LNA SMA Wireless Transceiver Antenna and add some extra pipelines, buffers, and an auto-retransmit feature – very nice!
This board features a reverse polarized SMA connector for maximum RF range. And there is PA and LNA circuit on board, with the external antenna it can reach long distance than the one without these parts.
This module comes with the 2.4G antenna (2DB), with a 250Kbps transmission rate on open-air it can reach the 800-1K meters communication distance.
2.4INCH TFT SHIELD FOR UNO
In stock
Features:
- 2.4″ diagonal LCD TFT display, with bright 4 white-LED backlights, default state: on
- It can control the backlight to connect the transistor to a digital pin
- 240X320 Pixels, with colorful and 18-bit, 262,000 different kinds of shade
- 4-wire resistive touchscreen
- 8-bit digital interface, plus 4 control lines
2.54mm 1×40 Pin Female Single Row Header Strip
In stock
It is a 2.54mm 1×40 Pin Female Single Row Header Strip. It has a single row of 40 pins. Ideal for through-hole mounting.
2.54mm 2×40 Berg Strip Right Angle Female Connector
In stock
2×40 Berg Strip Right Angle Female Connector. Break it to the required number of pins.
Also, custom PCBs or general custom headers use these types of connectors.
These connectors are bent at a 90° angle, which is suitable for many applications where the connectors are many times like prototyping.