Shop
ROVER 6WDJ60L ROCKER BOGIE SUSPANSION HIGH TORQUE DIY ROBOTIC CHASSIS KIT
In stock
- Durable construction: Crafted from 1mm and 2mm MS materials for long-lasting reliability.
- High traction wheels:112mm diameter wheels ensure excellent grip on various surfaces.
- Powerful motors: Equipped with 60 RPM high torque 12V DC motors for robust performance.
- 6-wheel drive configuration: Enhances maneuverability and stability across different terrains.
- Rocker-bogie suspension: Provides smooth traversal over uneven surfaces and obstacles.
- Versatile applications: Ideal for learning robotics, DIY projects, and advanced research initiatives.
Rover BO4WD4WT Do It Yourself Chassis Kit
In stock
Inside Kit:
1. BO 60RPM DC Motors – 4
2. MG996R Metal Gear Servo Motors – 2
3. Ultrasonic Sensor – 1
4. RC Rubber wheels Dia 86mm – 4
5. 3D Printed Spacers
6. Wheel Couplings – 4
7. Req Nut and Bolts
8. Acrylic Parts
9. 1mm Thickness Brackets/Chassis Parts
10. Mechanical Assembly Parts
RP1 ELSS Reciever
In stock
Features:
- Optimized PCB design for better heat dissipation.
- LNA for better receiver range.
- PA for better telemetry range.
- Antenna Diversity for improved signal stability and range.
- Built-in a TCXO (temperature compensated crystal oscillator)
- Compatible with all 2.4GHz ExpressLRS modules and transmitters with built in 2.4GHz ExpressLRS
- RF Chip: SX1281
- Telemetry RF power: Max 100mw
- Maximum receive refresh rate: 500Hz / F1000Hz
- Minimum receiver refresh rate: 25Hz
- Firmware Version: ExpressLRS v3.0 pre-installed
- FW Target: RadioMaster RP3 Diversity 2400 RX
RPI DEBUG PROBE
In stock
Features:
- All-in-one USB-to-serial debug and UART bridge
- Both interfaces use a 3-pin debug connector
- Open-source Raspberry Pi Picoprobe software
- Three different types of debug cables to cover the vast majority of use cases
- plug and play” debugging of Raspberry Pi Pico and other microcontrollers- and microprocessor-based platforms.
RPI PI CASE PI 5 ORG
In stock
Features:
- Easy three-piece installation design
- ABS plastic Material
- Holes for mounting the pi inside the case
- Rubber pad grip at the bottom
- Enhance thermal management
- Precise access to all port and status LEDs with Symbols
- Engraved Raspberry LOGO on Top
RS232 to RS485 CONVERTER
In stock
HEXIN RS232 to RS485 serial port Data interface adapter Converter . It has electronic Interface At the side of RS-232 is a DB9 female(hole-type) connector and at the side of RS-485 is a DB9 male (needle-type) connector with connection board. It has Transmission Speed of 300-115200 bps.Common wire, doule wire, UTP or Shielding Line are used as a transmission Media.
RS485 TO TTL CONVERTER MODULE
In stock
TTL to RS485 module, RS485 to TTL signal, single-chip serial port, UART, lightning protection hardware, automatic flow direction control The power supply of this product is wide voltage (3.0V ~ 30V), which realizes the compatibility between 3.3V system and 5.0V system, and both 3.3V and 5.0V signals can be matched. This product is equipped with wiring terminals and silicone wire, used for direct wiring. All imported chips are used.
RS485 to TTL Converter Module V2
In stock
This RS485 to TTL Converter Module can support up to 800 meter of bus length. It has connections for RX,TX, +ve and GND, on one side, and other side has connection for RS485 bus. It also has the Indicators for the Receive and Transmit Signals.
RTL SDR USB DVB-T RTL2832U+R820T
In stock
Software Defined Radio Rtl Sdr Usb Dvb-t Rtlrtl2832u+r820t
RTL-SDR Blog R820T2 RTL2832U
In stock
This is an RTL-SDR software defined radio receiver with RTL2832U ADC chip, R820T2 tuner, 1PPM TCXO, SMA F connector and aluminium case with passive cooling. Tunes from 500 kHz to 1.7 GHz with up to 3.2 MHz of instantaneous bandwidth (2.4 MHz max stable, 3.2 MHz max if your application is tolerant to USB drops). (HF works in direct sampling mode – V.3 models and above only). Perfect for use as a computer based radio scanner with free software like SDR#, HDSDR, SDR-Radio, Linrad, GQRX or SDR Touch on Android. Works on Windows, MacOS, Linux, Android and even embedded Linux computers like the Raspberry Pi.
This model has several key improvements over other models. It uses the improved R820T2 tuner, has a 1PPM TCXO (2 PPM initial offset, 1 PPM temperature drift), has improved component tolerances and an SMA F connector. It also comes with a software activatable bias-tee circuit for powering external devices such as LNA’s and active antennas. It also has HF reception capabilities. Most standard RTL-SDR dongles can tune down to 24 MHz at the lowest. This model has hardware that unlocks the “direct sampling mode”, and allows for tuning down to 500 kHz. There is a built in 25 MHz low pass filter for optimizing this mode.
RTL-SDR Blog V3 R860 RTL2832U
In stock
he RTL-SDR BLOG V3 is a low-cost software defined radio USB dongle. Perfect for getting into projects that utilize software defined radios or just learning more about them.
The RTL-SDR Blog V3 is an improved RTL-SDR dongle. RTL-SDR dongles were originally designed for DVB-T HDTV reception, but they were found by hardware hackers to be useful as a general purpose SDR. The standard dongles are okay for DVB-T reception, but are just barely suitable for SDR users/experimenters. The RTL-SDR Blog V3 was redesigned with SDR user needs in mind, instead of DVB-T HDTV users who typically have more relaxed requirements.
RTL-SDR works hard to maintain a higher standard of quality for the BLOG V3 among the other entry level SDR dongles on the market such as upgraded antennas and an Aluminum case for better cooling. With a bandwidth up to 2.4MHz and a frequency range of 500kHz – 1766 MHz it’s a capable SDR at a great price.
RWH SH 106D Goodsky Relay
In stock
1) Sugar-Cube relay suitable for various applications. 2) Highly adapt to harsh conditions with high temperature and vibration. 3) Halogen Free series available. 4) Dimension : 19*15.4*15MM (L*W*H)MM
S-160 ESD Heat Insulation Working Mat 450X300mm
In stock
Features:
- High-Quality Silicone Material
- Anti Static Material
- Magnetic slots to hold a small part
- Bright Colour for easy view of small components
- Comes with various slots to store the small products like screws while repair work
- Several hole locations to set screws, IC chips, and small parts.
- Built-in scale ruler (0 ~ 36 cm ) on bottom section.
- Make your repair work easy.
- A good partner for a hot air gun.
S500 Multi Rotor Air PCB Frame with High Landing Gear for FPV Quad-Copter
In stock
This is a S500 Multi Rotor Air PCB Frame with High Landing Gear for FPV Quad-Copter.
The S500 Multi-Rotor Air PCB Frame serves as the up-gradation of the F450 Quadcopter Frame. It keeps everything that has made the F450 Quadcopter frame successful.It has an adjustable battery mount to achieve the perfect weight distribution and the bottom frame is ready to take a whole host of camera mounts and gimbals making it perfect for FPV and filming projects.
S550 Hexacopter Frame
In stock
The S550 hexacopter frame kit is an excellent strong lightweight Hexacopter frame with carbon fiber landing gear and a bonus built-in the printed circuit board (PCB) for neat and easy wiring. It comes with integrated PCB for neat and easy wiring. The added lift capacity of a hex configuration makes this frame for carrying larger payloads such as camera systems and other electronic components. This makes for an exceptional camera rig or simply a very agile and powerful multi-rotor frame for aerobatics.
It comes with pre-threaded brass sleeves for all of the frame bolts, so attaching the arms to the mainframe is done within few minutes. Also, it requires one size of bolt for the overall build and thus a unique one-size hex wrench which makes hardware mounting very convenient.
SAM Head Sucker Antenna for SIM900A SIM908 Board GSM Antenna
In stock
SAM Head Sucker Antenna for SIM900A SIM908 Board GSM Antenna comes with the 3-meter feeder cable. The Antenna base equips a magnetic base to make it easy to place your antenna anywhere at your convenience.
SanDisk Micro SD/SDHC 16GB Class 10 Memory Card
In stock
Give the power to your project with Sandisk Micro SD/SDHC 16GB Class 10 Memory Card. A1 series memory card, new and made for APP or operating system to load and run more faster and smoother ever before. With speed up to 98 MB/s Shoot, save and share more with high speed. Built to perform in harsh conditions, SanDisk Ultra microSDHC UHS-I cards are Moistureproof, temperature proof, shockproof, and X-ray proof.