Shop
MQ7 – Carbon (co)
In stock
MQ-7 CO Carbon Monoxide Coal Gas Sensor Module detects the concentrations of CO in the air and outputs its reading as an analog voltage. The sensor can measure concentrations of 10 to 10,000 ppm.
The sensor can operate at temperatures from -10 to 50°C and consumes less than 150 mA at 5 V.
This module provides both digital and analog outputs. The threshold level for digital output can be easily adjusted using the preset on the board. The MQ-7 sensor module can be easily interfaced with Micro-controllers, Arduino and etc.
MRP121 BREAKOUT V12 CAPACITIVE TOUCH SENSOR
In stock
This MPR121 is a capacitive touch sensor controller driven by an I2C interface. The chip can control up to twelve individual electrodes, as well as a simulated thirteenth electrode The MPR121 also features eight LED driving… pins, when these pins are not configured as electrodes, they may be used to drive LEDs. There a four jumpers on the bottom of the board, all of which are set (closed) by default.
MS 4525DO Air Speed Sensor And Pitot Tube Set for Pixhawk
In stock
Featuring a Measurement Specialties 4525DO sensor, with a 1 psi measurement range (roughly up to 100 m/s or 360 km/h or 223 mp/h), the Pixhawk Airspeed Sensor Kit enables a resolution of 0.84 Pa, with data delivered at 14 bits from a 24 bit delta-sigma ADC.
It also measures temperature to allow calculation of true airspeed from indicated airspeed using the MS5611 static pressure sensor on Pixhawk. Not influenced by the heat of nearby processing components, it is much closer to the air temperature than with previous analog sensor setups. Supported on all Pixhawk and PX4 autopilot generation boards, this kit comes with M3 / 6-32 mounting holes.
If you are flying multi-copters then you do not require this unit as it is only usable if you are using the fixed-wing code in the Pixhawk.
MS 4525DO Air Speed Sensor And Pitot Tube Set for Pixhawk
In stock
Features :
- Digital airspeed sensor
- Rubber tubing
- Pitot tube
- Four-wire I2C cable
MS1100 GAS SENSOR
In stock
MS-1100 VOC formaldehyde benzene concentration gas sensor module.It is mainly used to detect VOC gases such as formaldehyde, toluene and benzene. It is a semiconductor type sensor product widely used in ventilation equipment, ventilation fans, air filters,hoods and other equipment. With high sensitivity and stability, it can detect more than 0.1ppm of gas. It is suitable for detecting various organic volatile components such as formaldehyde, benzene and xylene in the air. It is small in size and cheap in price. It is widely used in various small household appliances. on.
MT 3608
In stock
Features :
- It’s efficient by up to 93%.
- It can source a good amount of current.
- It is an inexpensive converter module.
- It’s simple to adjust to get your desired increase in voltage.
Note:
- The input voltage should not exceed the maximum input voltage.
- Peak current output current is not more than 2A for input & output.
- Please be noted that the output voltage should be higher than the input voltage.
MT2213 935KV Brushless DC Motor Black Cap
In stock
If you are wandering to build a drone and don’t know what will be the best motor for you then worry no more, we have got your back. At Agarwal , we have everything for you to get started with your drone project. This motor provides a Motor kV of 935.
In the field of Multirotors, there are so many brands that are making drone motors but Emax is giving us the best quality of drone motor at an affordable price.
Emax brand gained more popularity in the market due to the highest standards for optimal performance and reliability.
MT3608 DC DC WITH USB
In stock
Voltage Adjustments:
The output voltage can be adjusted using the Potentiometer on the module. Turning the pot clockwise, will decrease the voltage, and counter clockwise, will increase the output voltage.
Connections:
- Vin+ = Input Voltage
- Vin- = Ground
- Micro USB Connector = Input Voltage
- Out+ = Output Voltage
- Out- = Ground
Precautions to be taken while using Module:
- The output voltage must be higher than input voltage.
- The input voltage must not exceed maximum input voltage specified.
- Peak Current Draw from output should not be more than 2A.
MT76813DBI ESP8266 Serial WIFI wireless Gain Antenna
In stock
The subject of the auction is a set of elements needed to perform the modification of the Raspberry Pi Zero W tile so that it is possible to connect an external WiFi antenna. With this modification, you will increase the WiFi range in your Raspberry Pi Zero W. Factory-new components, 100% functional.
Multi Band PCB Antenna
In stock
This is a PCB Antenna having a frequency of 698-960MHz, 1710-2690MHz & 3400 – 3800MHz with 2/ 2.5/ 3.5 dBi gain. PCB Antenna is a wireless device to receive and transmit signals, it has been widely used in telecommunication to communicate. This antenna comes with an IPEX MHF1 Female connector to connect with application. (We can also arrange your Required connector if you need the antenna in bulk quantity) One of the main reasons to use a PCB (printed circuit board) antenna is the reduced overall cost of the radio module.
Multi Output Voltage DC-DC 12V to 3.3V 5V 12V Power Module
In stock
Features :
- Output power on/off switch
- Two-row multiple pin outputs, easy to use and connect
- Red LED illuminates when input DC power is supplied and output is turned ON.
- Outputs
- 3.3V DC at 800mA maximum current
- 5.0V DC at 800mA maximum current
- 12V DC (the 12V output is directly connected to the input, i.e. with 12VDC input, this output will be 12VDC; with 9VDC input, this output will be 9VDC)
- Small and Handy Module.
- Dual-side plate design
- Easy to use.
MULTIMETER TEST PROD
In stock
Multimeter Test probe -(smd)pointed pin All Type Of Mesuring Testing Instrument.
Multitec 07 Heavy Duty Nipper
In stock
Features :
- H-12cm L-6cm W-50gm.
- A versatile tool for cutting copper and aluminum conductors from 0.8mm to 1.2mm.
- Made out of high-grade alloy steel with black oxide finish heat treated to 60 HRC on cutting edges.
- Suitable for dressing components on printed circuit boards.
- Handles made out of high-grade ABS plastics.
MX 4 Way Loud Speaker Terminal Mini
In stock
MX 4 way Loud Speaker Mini terminal used for your speaker connection. MX 4 way Loud Speaker Mini terminal has color coding systems for better identification of polarity. MX 4 way Loud Speaker Mini terminal will provide you safe and secure operation.
MX1.25mm Pitch Connectors and Pre-Crimped Cables Silicone 15cm Wire
In stock
MY1016 24V 350W High Speed Motor Kit
In stock
My1016 Motor is quite powerful with its small size and extremely reliable with its power requirements. We’ve sold these for so many different applications that they were never designed for, but the robustness of the build makes them just go and go.
N20 12V 60rpm Micro Metal Gear DC Motor
In stock
Features
- High Torque Performance: The N20 6-12V 60RPM metal gear motor stands out with its high torque capabilities. And also ensure it can easily handle device who need robust and powerful rotational force.
- Dust Cover Protection: It also Feature a built in dust cover. This N20 dc gear motor is well protected against external particles. The dust cover also ensure the motor work in various environment.
- Waterproof Design: With a waterproof design, the N20 60RPM dc gear motor is ready to perform in harsh conditions. Its waterproof features add an extra layer of durability, making it a versatile solution for applications where exposure to liquids is a concern.
- JST Wire Connectivity: The N20 6-12V 60RPM metal gear motor comes equipped with a JST wire. And also provide a easy and secure connection for easy use in electronic project. This feature streamlines the setup process, making it user-friendly for both hobbyists and professionals.
- Versatile Applications: Designed for versatility, this N20 dc gear motor is suitable for a range of applications, including robotics, DIY projects, and small machine. Its adaptability and durability make it a go-to choice for various projects where high rotational power is important.
N20 DC GEARED MOTOR KIT(WITH WHEEL)
In stock
The N20 Motor with Wheel is lightweight, high torque, and low RPM motor. N20 Motor with Wheel is equipped with gearbox assembly so as to increase the torque of the motor. It has a cross-section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter.N20 Motor with Wheel comes with excellent stall characteristics, can climb hills easily.
- This is a N20 Motor with Wheel, ideal for making robots.
- Lightweight, high torque and low RPM.
- Fine craftsmanship, durable, not easy to wear.