Shop
GY-302 BH1750 Light Intensity Module
In stock
This IC is the most suitable to receive the ambient light data for adjusting LCD and Keypad backlight power of the Mobile phone. It is possible to detect wide range at High resolution.
GY-BME280-3.3 Precision Altimeter Atmospheric Pressure Sensor Module
In stock
GY-BME280-3.3 BME280 Atmospheric Pressure Sensor Module is a Breakout Board featuring a Bosch Sensortec ME280 Temperature, Humidity & Pressure Sensor.
The board has selectable I2C address jumper (solder link GS2), I2C pull-up resistors, 7 pin header 2.54mm, and two mounting holes 3.5mm.
Default setting of the board; single power rail Vdd=Vdd_IO (solder link GS1), pull-ups resistors (R2, R3) 10k, protocol selector resistor 0ohm (R1), decoupling capacitors 0.1uF on both power supply pins Vdd & Vdd_IO.
If you connect board to both power rails VDD_IO 1.8V and VDD 3.3V be sure to remove the power rail jumper GS1!
GY-MAX31865 Module
In stock
- Integration Lowers System Cost, Simplifies Design
- Efforts, and Reduces Design Cycle Time
- High Accuracy Facilitates Meeting Error Budgets
- 15-Bit ADC Resolution; Nominal Temperature
- Resolution 0.03125NC (Varies Due to RTD Nonlinearity)
- Total Accuracy Over All Operating Conditions:
- 0.5NC (0.05% of Full Scale) max
- Fully Differential VREF Inputs
- 21ms (max) Conversion Time
- Integrated Fault Detection Increases System Reliability
- 45V Input Protection
- Fault Detection (Open RTD Element, RTD Shorted to Out-of-Range Voltage, or Short Across RTD Element)
GY-SI5351 Clock Signal Generator Module
In stock
The Si5351A clock generator is an I2C controller clock generator. It uses the onboard precision clock to drive multiple PLL’s and clock dividers using I2C instructions. By setting up the PLL and dividers you can create precise and arbitrary frequencies. There are three independent outputs, and each one can have a different frequency. Outputs are 3Vpp, either through a breadboard-friendly header or, for RF work, an optional SMA connector.
GY530-VL53L0X TOF RANGE SENSOR – Purple
In stock
Features:
- GY-530 VL53L0X ToF Sensor
- Time-of-Flight for accurate distance
- VL53L0X for precise ranging
- Compact design
- Unsoldered components
- Purple color
- Ranging time: <30ms
- Standby power consumption: 5μA
GY56 VL53L0X Yellow Org
In stock
Provide Arduino, 51, stm32 microcontroller communication program. GY-56 can set the upper and lower limit distance alarm value, switch output, In the set interval, there is a block of the measured object and a high level is directly output. Under the IIC mode, you can set different internal IIC addresses if necessary.
H16 RC Skydroid
In stock
Remote Controller
- Model No.: H16
- Working Voltage: 4.2V
- Frequency: 2.400 to 2.483GHz
- Endurance: 6-20 Hours
- Channels: 16
- RF Power: 20DB@CE/23DB@FCC
- Battery: 20000mA/H
- Charging Port: Type-C
- Weight: 1034g
- Size: 272 x 183 x 94mm
Receiver
- Model No.: R16
- Working Voltage: 7.2 to 72V
- Channels: 16
- RF Power: 20DB@CE/23DB@FCC
- Weight: 90g
- Size: 102.1 x 42.6 x 36.5mm
Hall Sensor Module A3144E
In stock
This is a Comparator based LM393 Linear Hall Effect Sensor Module. This Module is based on S49E linear hall effect sensor. Using this module you can get digital as well as linear output. This module can be used to detect the presence of a magnetic field. If there is a magnetic field present, it will report a high-level signal. It can be used in many applications such as RPM sensor (for counting the number of shaft revolutions), Robot speed and distance measurements, door switch and robot arm position sensor. Generally, it can be used for any magnetic field detection. This Product is known as Hall Effect Sensor Module, Linear Magnetic Hall sensor, Magnetic Hall sensor, Magnetic sensor, Module, Sensors and Modules, KY-024 Linear magnetic Hall Sensor, KY-024 magnetic Hall Sensor, KY-024 magnetic Sensor, Linear Magnetic Hall Effect Sensor Module.
Hall Sensor Only A44E
In stock
“Hall effect Sensor 44E is a switched hall-effect IC which is for contact less switching applications.The device includes an on-chip Hall voltage generator for magnetic sensing, an amplifier that amplifies the Hall voltage, a schmitt trigger to provide switching hysteresis for noise rejection, and an Digital Output Hall-effect sensor.Suitable for Automotive and Industrial Applications. 3V To 30V hall Effect Switch/Magnetic Sensor Working Voltage.”
Hall Sensor Only AH49E
In stock
Hall Effect Sensor-AH49E is a small, versatile linear Hall-effect device that is operated by the magnetic field from a permanent magnet or an electromagnet. The output voltage is set by the supply voltage and varies in proportion to the strength of the magnetic field. The integrated circuitry features low noise output, which makes it unnecessary to use external filtering. It also includes precision resistors to provide increased temperature stability and accuracy. The operating temperature range of these linear Hall sensors is -40°C to +85°C, appropriate for commercial, consumer and industrial applications.
HC-05 6pin Bluetooth Module with Button
In stock
HC-05 6 Pin Wireless Serial Bluetooth Module is a Bluetooth module for use with any microcontroller. It uses the UART protocol to make it easy to send and receive data wirelessly.
The HC-06 module is a slave only device. This means that it can connect to most phones and computers with Bluetooth but it cannot connect to another slave-only device such as keyboards and other HC-06 modules. To connect with other slave devices a master module would be necessary such as the HC-05 version which can do both master and slave.
HC-06 TTL Bluetooth Transceiver Module
In stock
The Bluetooth Transceiver HC-05 TTL Module with enable/disable button Breakout is the latest Bluetooth wireless serial cable! This version of the popular Bluetooth uses the HC-05/HC-06 module. These modems work as a serial (RX/TX) pipe.The remote unit can be powered from 3.3V up to 6V for easy battery attachment. All signal pins on the remote unit are 3V-6V tolerant. No level shifting is required.
HC-12 433 SI4463 Wireless Serial Module
In stock
HC-12 wireless RF UART communication module is a new generation of multi-channel embedded wireless data transmission module. The Radio frequency of 433.4 – 473.0MHz, can be setting a communication channel, step is 400kHz, a total of 100 channels. The module maximum transmit power is 100mW (20dBm), and -116dBm receiver sensitivity air of the 5000bps baud rate, communication distance about 500 meters.
The module adopts a stamped hole encapsulation method, which can be welded. The module size is 27.4mm*13.2mm *4mm (including antenna seat, not including the spring antenna), which is convenient for the customer to be embedded in the application system. The module has a PCB antenna seat ANT1, users can use the coaxial cable, the use of 433MHz band external antenna.
HC-SR04 ULTRASONIC SENSOR 4PIN
In stock
- Measures the distance within a wide range of 2cm to 400cm
- Stable performance
- Accurate distance measurement
- High-density
- Small blind distance
HC12 SI4463 Wireless Serial Module 1000M With Antenna
In stock
HC-12 wireless RF UART communication module is a new generation of multi-channel embedded wireless data transmission module. The Radio frequency of 433.4 – 473.0MHz, can be setting a communication channel, step is 400kHz, a total of 100 channels. The module maximum transmit power is 100mW (20dBm), and -116dBm receiver sensitivity air of the 5000bps baud rate, communication distance about 500 meters.
The module adopts a stamped hole encapsulation method, which can be welded. The module size is 27.4mm*13.2mm *4mm (including antenna seat, not including the spring antenna), which is convenient for the customer to be embedded in the application system. The module has a PCB antenna seat ANT1, users can use the coaxial cable, the use of 433MHz band external antenna.
HDMI FEMALE SOCKET
In stock
HDMI Female to Mini HDMI Male Adapter
In stock
The HDMI Female to Mini HDMI Male Adapter eliminates the need for multiple cables and clutter. It is a cost-effective way of connecting HDMI Mini-enabled devices to standard HDMI ports.It Supports Audio Return Channel (ARC), HDMI Ethernet Channel (HEC), 48 Bit Deep Color, 32 channel audio, HDCP, Dolby True HD 7.1 audio, and 3D video, also Supports resolutions up to 4Kx2K (UHD) including 4096×2160, 3840×2160, 2560×1600, 2560×1440, 1920×1200, and 1080p.
HDMI Male to VGA Female Converter
In stock
HDMI male to VGA female adapter is the most convenient and cost-effective solution for connecting your HDMI devices to your VGA monitors or projectors.
Our HDMI male to VGA female adapter features a built-in active IC chip which guarantees almost 100% compatibility. Choose to “Mirror” your computer screen for a presentation on a projector or “Extend” your desktop to view more applications on a monitor.