Shop
GNSS Receiver BOB with IRNSS
In stock
L1, L5 signal reception to support GPS and NavIC. Works with NavIC, GAGAN, GLONASS,
GPS satellites and more. Support for AGPS.
Support for Automotive Dead Reckoning (ADR), Odometer-less Dead Reckoning (ODR) with either built-in sensors within the GNSS BOB or with external sensors.
Optional Real-time Kinematic (RTK) module for Centimetre level precision and accuracy.
Less than 33 second cold start TTFF.
~1 second hot start.
~2.5m CEP accuracy.
Works from external 5V±5%, ≤120mA DC input.
Provision for RTC Battery (MS621FE-FL11E-not populated)
Easy to use
Easy to install
Good quality product
Gold Aluminum Heat Sink Case with Double Fans
In stock
This is a must-have accessory to experience the high performance of the Raspberry Pi 4 Models. The Aluminium Alloy Case with Double Dual Cooling Fan Heat Sink Metal Case is designed especially for Raspberry Pi 4 Model B.
This is a premium quality heat sink for industrial and continuous use applications for the Raspberry Pi 4. This heat sink enables the Raspberry Pi to function with very high reliability and at higher efficiencies for applications which require the maximum computing power of the Pi 4.
GPS Antenna Foldable Mount Holder
In stock
It is Plastic GPS Antenna Foldable Mount Holder Seat Base Folding Bracket Holder DIY Drones FPV 250 Quad Copter Multi Copter. This GPS folding antenna mount holder makes your GPS module mount with a convenient folding option on quad multi helicopter by just using multi-rotor 2 screws. Fold down your robust build capability and position it down.
GPS NEO-7M Satellite Positioning Module Development Board for Arduino STM32 51
In stock
This GPS module is based on the NEO-7M and can be used for satellite positioning. The module supports NMEA standard protocol output, and built-in FLASH, and can save the setting information after power-off without external EEPROM. This module has an onboard ceramic antenna, which can easily locate the satellite in an open place without an external antenna. It is also welded with an SMA head, which can be used for an external antenna, to make the search positioning ability stronger. When using, you can debug the GPS module using the data cable via the micro USB interface. Or through the reserved serial port interface, use USB to serial port modules or external MCU to receive the GPS
Graphic LCD Display 128×64 Green Color
In stock
LCD Module 128×64 has various different models on shelf and accept custom develop to meet your special requirement. We can develop different interface like I2C, Serial, and we also have different font available. This Display is professional Monochrome LCD display for Industry application, include digital panel meter, UPS, inverter, multi-function meter, POS machines, Fuel Dispenser, Oil Dispenser, Gas Dispenser, Flow Meter, KWH Meter, Energy Meter, Water Meter, Gas Meter, Smart Meter, Clock. Our Graphic LCD Module 128*64 has various different models on shelf and accept custom develop to meet your special requirement. We can develop different interface like I2C, Serial, and we also have different font available.
GSM 4G/3G/2G 6/7 dBi Dual Band LTE Flexible Magnetic Mount Antenna
In stock
This is GSM 4G/3G/2G LTE Flexible Magnetic Mount Antenna having Frequency of 698 – 960 MHz & 1710 – 2690 MHz and 6/ 7 dBi Gain. This antenna is supported to GSM FCT of Micromax, and other GSM Module/Modems. Magnetic mount antennas are commonly used for car and truck applications. The antenna’s magnetic base sticks securely to the metal of the vehicle. The metal surface of the car acts as a ground plane to bounce the signal. Since magnetic mount antennas require a ground plane, they should be mounted on metal.
GSM Antenna SMA 5cm 900M 1800mhz
In stock
This is a 2dBi Gain Dual Band 3G / 4G LTE Antenna with an SMA-Male connector having a frequency of 900M 1800mhz
This compact GSM900/1800 omnidirectional “rubber-duck” GSM antenna provides broad coverage. It is a coaxial sleeve design with an omni-directional pattern.
This antenna was also designed to transmit on the 900mhz frequencies with a top end transmission not to exceed 25 watts. Works for the current Mobile Communication.
GSM SIM800C Modem with Antenna
In stock
GSM SIM800C Modem with Antenna Module’s baud rate is configurable from 9600-115200 through AT command. The GSM GPRS Modem is having internal TCP/IP stack to enable you to connect with the internet via GPRS. It is suitable for SMS, Voice as well as DATA transfer applications in the M2M interface.
The onboard Regulated Power supply allows you to connect a wide range of unregulated power supply. Using this modem, you can make audio calls, SMS, Read SMS, attend the incoming calls and internet, etc through simple AT commands.
The Modem is built with Quad-Band GSM/GPRS engine-SIM800C from SIMCOM, works on frequencies 850/ 900/ 1800/ 1900 MHz.
GT Power Multi Servo Tester
In stock
GT POWER 3-Channel Multi Servo Tester offers 3 modes to check servos or ESC. The Manual Mode allows you to turn the knob to different speeds and check the reaction time. The Neutral mode makes the servo go back to the neutral point. The Automatic ’’Window Wiper’’ Mode makes the servo swing like a window wiper in the largest angle possible.
GY – 9250 MPU-9250 9 Axis Sensor Module Gyro+Accel+Magn
In stock
MPU9250 9-Axis Attitude Gyro Accelerometer Magnetometer Sensor Module features the MPU-9250, which is a multi-chip module (MCM) consisting of two dies integrated into a single QFN package. One die houses the 3-Axis accelerometer and gyroscope. The other die houses the AK8963 3-Axis magnetometer. Hence, the MPU-9250 is a 9-axis Motion Tracking device that combines a 3-axis accelerometer, gyroscope and magnetometer, and a Digital Motion Processor (DMP). It is based on I2C Address, Address: 0x68 by default, 0x69 if AD0 is pulled high.
GY-271 HMC5883L 3-axis Electronic Compass Module
In stock
This compact sensor fits into small projects such as UAVs and robot navigation systems. The sensor converts any magnetic field to a differential voltage output on 3 axes. This voltage shift is the raw digital output value, which can then be used to calculate headings or sense magnetic fields coming from different directions.
GY-302 BH1750 Light Intensity Module
In stock
This IC is the most suitable to receive the ambient light data for adjusting LCD and Keypad backlight power of the Mobile phone. It is possible to detect wide range at High resolution.
GY-BME280-3.3 Precision Altimeter Atmospheric Pressure Sensor Module
In stock
GY-BME280-3.3 BME280 Atmospheric Pressure Sensor Module is a Breakout Board featuring a Bosch Sensortec ME280 Temperature, Humidity & Pressure Sensor.
The board has selectable I2C address jumper (solder link GS2), I2C pull-up resistors, 7 pin header 2.54mm, and two mounting holes 3.5mm.
Default setting of the board; single power rail Vdd=Vdd_IO (solder link GS1), pull-ups resistors (R2, R3) 10k, protocol selector resistor 0ohm (R1), decoupling capacitors 0.1uF on both power supply pins Vdd & Vdd_IO.
If you connect board to both power rails VDD_IO 1.8V and VDD 3.3V be sure to remove the power rail jumper GS1!
GY-MAX31865 Module
In stock
- Integration Lowers System Cost, Simplifies Design
- Efforts, and Reduces Design Cycle Time
- High Accuracy Facilitates Meeting Error Budgets
- 15-Bit ADC Resolution; Nominal Temperature
- Resolution 0.03125NC (Varies Due to RTD Nonlinearity)
- Total Accuracy Over All Operating Conditions:
- 0.5NC (0.05% of Full Scale) max
- Fully Differential VREF Inputs
- 21ms (max) Conversion Time
- Integrated Fault Detection Increases System Reliability
- 45V Input Protection
- Fault Detection (Open RTD Element, RTD Shorted to Out-of-Range Voltage, or Short Across RTD Element)