Shop
DhT-11 Module
In stock
The DHT-11 Digital Temperature And Humidity Sensor is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air and spits out a digital signal on the data pin (no analog input pins needed).
DHT-22 MODULE
In stock
If you are wandering to build a device that detects temperature and humidity from the atmosphere, then This sensor is needed for you.
The DHT22 Digital Temperature and Humidity Sensor Module AM2302 is a basic, low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air and spits out a digital signal on the data pin (no analog input pins needed).
Digital 13 DOF bipedal Humanoid DIY Robot
In stock
It Provides you a Made in India classic 13-degree-of-freedom Humanoid robot is inspired by industrial machines. It is suitable for users of college students, middle school students, etc. Humanoid Robot, Completely Programmable.
Digital Display for HC-SR04 Ultrasonic Distance Measurement Control Board
In stock
Digital Display for HC-SR04 Ultrasonic Distance Measurement Control Board adopts 8 bit MCU as the main control chip; it can be applied in distance measurement, testing HC-SR04 ultrasonic module performance. And it supports serial port display and digital tube display.
Digital Multi Servo Tester ESC RC Consistency CCPM Master Speed Control
In stock
The Digital Multi Servo Tester ESC RC Consistency CCPM Master Speed Control offers 3 modes to check servos or ESC. The Manual Mode allows you to turn the knob to different speeds and check the reaction time. The Neutral mode makes the servo go back to the neutral point. The Automatic ’’Window Wiper’’ Mode makes the servo swing like a window wiper in the largest angle possible.
DIGITAL MULTIMETER HTC INSTRUMENT DM-81
In stock
Features:
- 3 ½ Digital Multimeter with Manual Range
- Live Wire Recognition
- Live Remote Control Testing
- Full Overload Protection
Digital Sensor TTP223B Module
In stock
Digital Capacitive Touch Switch Module is based on TTP223B. Normally, it outputs low and keeps at low power state. When a touch is sensed on the circular marked region, it outputs high and switches to the quick response state. When not being touched for 12 seconds, it switches to low power state again.
Digital Servo Tester / ESC Consistency Tester
In stock
Features:
- 1.18” Screen Display
- Easy to Read 4 Digit 7 segment Screen
- 7 servos can be output and controlled synchronously
- An adjustable rotary potentiometer can reduce or increase the width of the output pulse.
Digital Servo Tester / ESC Consistency Tester
In stock
Features:
- 1.18” Screen Display
- Easy to Read 4 Digit 7 segment Screen
- 7 servos can be output and controlled synchronously
- An adjustable rotary potentiometer can reduce or increase the width of the output pulse.
Dipole Pentaband Waterproof Antenna
In stock
A unique solution to connect your smart devices to the cloud. The antenna supports GSM 850/900/1800/1900 MHz and UMTS bands. Designed for small devices, this antenna will work when used as a wireless terminal, gateway or access point. It is a ground plane independent design, housed in a rugged waterproof plastic casing. It can be used outdoors in any type of telemetry project, as well as for discreet in-vehicle installations. It comes with high-quality adhesive tape that allows the antenna to adhere to any surface. Please note that the antenna is not designed to be mounted on large metal surfaces as this will affect the antenna coverage.
Discovery kit with STM32F051R8 MCU, DK32F051R
In stock
Based on the STM32F051R8T6, it includes an ST-LINK/V2 embedded debug tool, LEDs, pushbuttons and an additional prototyping board for easy connection of additional components and modules.
The STM32F0DISCOVERY helps you to discover the STM32F051xx Cortex®-M0 features and to develop your applications easily. It includes everything required for beginners and experienced users to get started quickly.
DISSOLVE OXYGEN SENSOR WITH PH BOARD
In stock
Preparing the Dissolved Oxygen Level Sensor Probe:
For a new dissolved oxygen probe, first thing to remember begin by adding 7.5% KCL solution into the membrane cap as the filling solution. Follow these steps:
- Remove the membrane crown.
- Place the DO membrane on the cap and fix the crown to the electrolyte tube, covering one side of the membrane.
- Ensure the membrane has no wrinkles and is not punctured or damaged.
- Unscrew the membrane cap from the probe and fill about 2/3 volume of the cap with KCL solution.
- Keep the probe in a vertical position concerning the horizontal plane.
- Carefully screw the cap back onto the probe. Some solution overflow is acceptable to ensure the probe is fully filled with KCL solution, eliminating air bubbles.
- The 7.5% KCL solution acts as a suitable electrolyte in the DO Probe.
- The electrode tube should be free of air bubbles to prevent fluctuations in readings.
DIY Acrylic Robot Manipulator Mechanical Arm Kit (not-including Servo and Board)
In stock
It is a DIY Acrylic Robot Manipulator Mechanical Arm (not-including Servo and Board). The arm has 4 DOF. The mechanical parts are laser cut to precision and are versatile to use.
DIY BLUETOOTH CONTROLLED ROBOT
In stock
An Arduino Bluetooth robot is a fascinating project that combines the versatility of Arduino with the wireless communication capabilities of Bluetooth technology. This type of robot typically involves integrating an Arduino microcontroller with a Bluetooth module and various sensors or actuators to create a remotely controlled robot.
**Bluetooth Module:** A Bluetooth module, such as HC-05 or HC-06, enables wireless communication between the robot and a Bluetooth-enabled device like a smartphone or a computer.
Diy Kit 16No Tank
In stock
- Colour:Black And White.MOBILE WITH GRIPPER AND GEARBOX MODULE DO IT YOURSELF
- MOBILE PLATFORM ROBOTIC ROBOT REMOTE PROJECTS
- DO IT YOURSELF DIY LEARNING KIDS ROBOT TEACHING PHYSICS
- ROBOT FOR SCHOOL KIDS ENGINNERING STUDENTS HOBBY