Shop
CNC shield V3 for Engraving Machine A4988 DRV8825 driver expansion board
In stock
This expansion board as a driver expansion board, can be used for engraving machines, 3D printers, CNC. It is a total of four slots, can drive four A4988 stepper motor. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors.
The CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board is very convenient to use.
After insert Arduino CNC Shield V3.0 into Arduino UNO, and installed GRBL firmware then you can quickly DIY a CNC engraving machine.
Coin Acceptor MULTICOIN
In stock
How to Configure the Vending Machine Coin Acceptor (Multi-Coin Acceptor):
- Press the setting key (8) to choose several currency systems.
- Use the accurate key or broaden key to increase or decrease the numerical value.
- Press the setting key once the setup is complete to confirm.
- The letter H will appear in the sentence (the quantity of sampling for various currency values).
- The letter P will appear in the sentence (the numerical value for signal output of various currency values).
- The letter F will appear in the sentence (the precision of various currency values).
- Set the desired money according to the parity of argumentation.
- Turn off the power when the letter E appears so that it can reopen.
The multi-coin reader machine can take up to six different kinds of coins and tokens from across the world. It has an integrated intelligent CPU software control for high accuracy. Self-programming features are also included. It guards against electromagnetic interference and electrical shocks.
COLOR SENSOR TCS3200
In stock
GY-31 Color Sensor Module is made using IC TCS3200, a programmable color light to a frequency converter. It has configurable silicon photodiodes and a current to frequency converter in a single monolithic CMOS Integrated Circuit. Its output is a square wave having a 50% duty cycle with frequency directly proportional to irradiance (light intensity). This module can be directly interfaced with Microcontrollers, Arduino Boards, Raspberry Pi, etc.
Condensor Mic
In stock
Buy the new Voice Microphone online at Robu.in. This Voice microphone is Multi-Channel and is suitable for mobile phones, telephones, tape recorders, voice-activated toys, computers, and other products. The sensitivity is in accordance with the IEC standard, and the sensitivity of “pa” is increased by 20dB, which is the same as the sensitivity of the “Ubar” unit.
Connector 2500 2 Pin Female
In stock
Xinya XY2500 2 Pin Female Pluggable Terminal is Right Angle Terminal and It’s suitable connector for the wire to Board connectors in various industrial as well other electronics products. It is suitable for use where the PCB placement is inside enclosure, and connections should be accessible from outside. In this the wires are secured with screw in the connector.
Connector 2500 2 Pin male
In stock
Xinya XY2500 2 Pin Close Type Male Terminal is Close Type Right Angle Pluggable Terminal and It’s suitable connector for the Board to Wire connectors in various industrial as well other electronics products. It is suitable for use where the PCB placement is inside enclosure, and connections should be accessible from outside.
CONNECTOR XY 129 2 PIN
In stock
Its a Xinya XY129 2 pin Screw Terminal. The XY129 Series Screw Terminal comes with current rating of 20A, and can accept wire of 26-12AWG or 2.5mm². This screw terminals can withstand up to 2000VAC/60s.
Connector XY126 2 Pin PBT BIG
In stock
This is a 126 2 Pin Screw Terminal. The 126 Series screw terminals have current capacity of upto 6A. This screw terminals are widely used in all kinds of electronics devices for connecting the wires. They accept wires of 26-14 AWG or 2.5mm2. The maximum rated voltage is 300V @ 10A.
Connector XY126 3 Pin PBT BIG
In stock
This terminal block has screws to keep the wires in place. It can hold wires from 16 to 24 AWG. This terminal block is Featured by Sharvi Electronics ideally suited to miniature rack systems or telecoms equipment, which demand high contact density. As each terminal has a single corresponding pin spaced every (5 mm), these terminal blocks can be used with prototyping boards and PCB holes intended for standard male and female headers (if there is sufficient clearance from nearby components).
CONTROL HORN + U CLEVIS SET FOR RC PLANE NYLON
In stock
The nylon control horns are used to connect control surfaces such as rudders and ailerons to the airplane. The nylon control horns sandwich the control surface between the two horn bases and offer a no slip installation. The backplate pushes over the teeth on the horn and locks it into place, no need for glue or screws. This set also includes a compatible Nylon clevis for threaded or push fit rods. It has a shaft on the side for a 2mm grub screw for secure fixing.
COPPER CLAD 6X4 DOUBLE SIDE
In stock
Features of Copper Clad PCB Board (6 x 4 Inch):
- Dissolve readily in safe and inexpensive solvents, so are easy to use for impregnating
- Adhere well to both copper foil and electro less copper
- Bond well to glass fiber finished with epoxy
- Drill easily (bits are deflected by the glass fibers, rather than the resin)
- Can be formulated to be flame-retardant
Applications of Copper Clad PCB Board (10X15 cm):
- It is used to make PCB manually
- Multiple DIY projects
COPPER CLAD 6X4 SINGLE SIDE Paper phenolic
In stock
This is a good quality Phenolic PCB board. It is also known as Copper Clad Board. This board can be used to build your own circuit boards, breakout boards, DIY board and other Industrial boards and applications. This board is made of high-quality phenolic laminate and has size of 6X4 inches.
CP2102 Converter RED
In stock
Serial Converter CP2102 USB 2.0 to UART TTL 5PIN Connector Module The CP2102 is a highly integrated USB2.0 full-speed function controller with a built-in USB transceiver, and crystal oscillator, EEPROM, and asynchronous serial data bus (UART) to support a full-featured modem signal without the use of any external USB devices. CP2102 USB-UART switching circuit by the driver into the PC’s USB port virtual COM port expansion to achieve the purpose, similar to other works.
CP2102(6-pin) USB 2.0 to TTL UART serial converter
In stock
This is the CP2102(6-pin) USB 2.0 to TTL UART serial converter module. This is a great little tool for embedded systems that require a serial connection to a computer. The board can simply attach to a USB bus and will appear as a standard COM port.
CPU MALE SOCKET
In stock
AC power socket Male with switch to connect your computer system to the commercial power supply. sockets are male electrical connectors which accept and deliver current to the prongs of inserted plugs. Sockets are designed to accept only matching plugs and reject all others.
CPU SOCKET WITH FUSE AND SWITCH (HOLES)
In stock
EC320 C14 male plug, 3-pin terminals, durable material construction, long using life. This power socket is fitted with Neon Indicator On/OFF switch and fuse. Used widely in lab equipment, fitness equipment, industrial automation equipment, etc. Fit for a fuse with 5x20mm size. Use only with a 250V fuse (Fuse is not included).
CPU SOCKET WITH FUSE HOLDER
In stock
This is an IEC320 C14 Male Power Cord Inlet Socket with Fuse Holder for power ratings AC 250V 15A.