Shop
6AWG SILICONE WIRE ( BLACK )
In stock
It is super flexible and soft with a high strand count which means it is great for use in restrictive and compact areas. The wire is the first priority tool for carrying current from one circuit to other while their current carrying capacity is dependent upon the size of the wire. So the High-Quality 6AWG Silicone Wire 1m (BLACK) has the considerable diameter to suit your application.
6inch Hub Motor + Controller 24V350W
In stock
E-bikes generally combine both pedal-assist sensors as well as a throttle. Some electric bikes have an electric motor that operates on a power-on-demand basis only. In this case, the electric motor is engaged and operated manually using a throttle, which is usually on the handgrip just like the ones on a motorbike or scooter.
This is a 6 Inch 350w 24v Brushless Hub Motor with Tyre for E-bike. This monster Hub Motor is for Self-balancing Cars & Scooters.
We are offering a good knowledge base and technical support to our customers for the assembly of the E-bikes.
6S BMS 40A
In stock
- Small size designed for a four-cell battery pack.
- Simple and convenient circuit for easy connections
- Over-charge/Over-discharge Protection.
6V Mini Dosing pump
In stock
When pumping liquids and no direct contact with the liquid is required, the all-new range of peristaltic pumps from kamoer offers a simple solution. Unlike most pumps, peristaltic pumps squishes a silicone tube to produce the pump-action instead of impelling it directly, thus no direct contact with the liquid. This pump requires a 6 V DC supply and can produce a flow rate of up to 10.5 ml per minute. If speed control is required we suggest using a simple PWM signal.
6V Relay Cube
In stock
These are high-quality Single Pole – Double Throw (SPDT) sealed 6V Sugar Cube relays. Use them to switch high voltage (240AC), and/or high current devices(7A).
6W DIY Kit
In stock
AM ROBOTICS DIY ROVER 6WD BO60 V3 comes with Matt finished metal chassis. Included 6 BO dual shaft 60 RPM motors, 6 rubber wheels, two in one screwdriver set, spanner, Two ultrasonic sensors, Four sg90 servo motors, 2-Axis Servo Pan Tilt, Jumper Wires, assembly manual and all required screws. Compatible with Arduino, raspberry, etc. Easy to assemble. Assembly manual provided in the kit. By using this easy to assemble kit. All required components, sensors, and tools provided in the kit.
7 X 9 CM Universal PCB Board Double-sided
In stock
This is a Universal PCB Prototype Board Double-Side 7 X 9 CM High-quality universal prototyping board with standard 0.1″ spacing through holes.
High-quality 7 X 9 CM FR4 material, Double-sided, HASL, NC CNC drilled.
7″ Official Raspberry Pi Display with Capacitive Touchscreen
In stock
The 7″ Official Raspberry Pi Display with Capacitive Touchscreen gives users the ability to create the all-in-one, integrated projects such as tablets, infotainment systems, and embedded projects!
The 800×480 display connects via an adapter board which handles power and signal conversion. Only two connections to the Pi are required; power from the Pi’s GPIO port and a ribbon cable that connects to the DSI port present on all Raspberry Pi’s. Touchscreen drivers with support for 10-finger touch and an on-screen keyboard will be integrated into the latest Raspbian OS for full functionality without a physical keyboard or mouse
7015 Black 12VDC Smart Cooling Fan
In stock
This is a 70 x 70 x 15 mm smart cooling fan. It has a four-wire input. The purpose of four-wire is possible revolution measuring with low fan speeds and precision control of revolution in all speed ranges providing a PWM signal to the fan according to the cooling requirement.
702PCS DIY Blocks Education Set – Programming Robot – Mechanical Power Kit
In stock
What is in the box?
- Power 1, Wire tap 2, Dark 1, Distance 1, IR 1, Lamp 1, Buzz 1, Invert 1, Motor driver 2, Motor 2, Wheels 2, 9v Battery 1, , Makers badge 1,, Instruction mannual 1, Warranty Card 1, Wire 5, Power Snap 1,Wit bricks (Building Blox ) 136
74hc4067 16ch Mux Board
In stock
Features
- “On” resistance: 70 Ohms @ 4.5V
- 6ns break-before-make @ 4.5V
On the electronics module there are 2 rows of header solder points. These can be used to connect wires to or header pins depending on the application.
- 1×8 Header Location
- SIG = Signal Input / Output. This will usually connect to an analog input or digital I/O on the microcontroller
- S3 = Binary Address Bit 3. The address bits (3…0) connect to 4 digital output pins on the microcontroller to select channel.
- S2 = Binary Address Bit 2
- S1 = Binary Address Bit 1
- S0 = Binary Address Bit 0
- EN = Enable. Internally pulled LOW to enable by default. Can be pulled HIGH to disable all channels.
- VCC = 2 to 6V. Usually connected to 5V or 3.3V to match the microcontroller power.
- GND = Ground, must be common with the microcontroller.
- 1×16 Header Location
- C15 = Channel 15
- C0 = Channel 0
7530 12V DC Blower Cooling Fan
In stock
7530 12V DC Blower Cooling Fan made of special and premium materials. It is high temperature resistant and extremely durable. Excellent for cooling heat sinks on hot ends, prints, or other cooling needs. This blower fan has projector blower centrifugal fan for powerful air throw.
It is made of high quality PBT+30% glass line +VO and Bearing with high precision make it provide long life and low noise. It can be taken in use to handle the temperature cooling 75℃. Its Working temperature 40℃ with the continuous working of 24 hours capacity.
75pc-GEAR SET
In stock
These gears are used in laboratories, science education, and DIY models and RC-airplane/helicopter repair, as well as many household repairs like old music system etc. its a great toolkit for promoting DIY abilities, improving children’s, teen’s hands-on skills and divergent thinking.
- Material: plastic;
- colour: white, orange, Blue, yellow
75w Element
In stock
Specification for 75 watt Soldering Element
- Type : Spare Soldering Element
- Watt : 75 Watt
- Voltage : 230 Volts
- Material : Stainless Steel
Additional Information :
- Manufacturer : Soldron
- Wattage : 75 Watts
775 12V DC MOTOR D Shaft
In stock
The D Shaft 775 12V DC Motor is a powerful and versatile device designed for high-speed and high-torque applications. With a rotation speed of 3000 RPM/MIN, this dual-shaft motor provides efficient performance. Its 12V operating voltage makes it suitable for various projects, offering a balance of speed and torque for a wide range of applications.
7X4 PULLEY WHEEL
In stock
Pulley wheel 6cm Dia. x 4cm Width is specially designed for conveyor belts. They have a groove running through the middle so that they restrict the belt from slipping. A 4 cm width belt is recommended with this pulley.