Shop
5MP Raspberry Pi Zero W Camera Module
In stock
The 5MP Raspberry Pi Zero W Camera Module W/ HBV FFC Cable equips flexible cable for attaching with Raspberry Pi Zero W. The 5MP camera module is perfect for small Raspberry Pi projects which have very little space allowance just boot up the latest version of Raspbian and you are good to go!!!
The high-definition 5MP camera delivers outstanding photos but can also shoot video, ideal for drones or a CCTV project.
5V SSR Omron Relay
In stock
To use this Relay you need to connect the control input (number 3) pin to the 5V GPIO pin of the microcontroller board you are using and number 4 pin to GND and if 5V supply is on the there will be contact between number 1 and number 2 load pins.
5V 0.35A 36ml/min Silicone Tube Liquid Pump
In stock
When pumping liquids and no direct contact with the liquid is required, the all-new range of peristaltic pumps from kamoer offers a simple solution. Unlike most pumps, peristaltic pumps squish a silicone tube to produce the pump-action instead of impelling it directly, thus no direct contact with the liquid. This pump requires a 5 V DC supply and can produce a flow rate up to 36ml per minute. If speed control is required we suggest using a simple PWM signal.
5V 1 Channel Relay
In stock
It is a 5V 1 Channel Without Light Coupling Relay. The relay normally open interface maximum load: AC 250V/10A, DC 30V/10A. It has a trigger current of 5mA, and module working voltage of DC 5V. Each channel of the module can be triggered by a jumper to set a high level or a low level. Fault-tolerant design, even if the control line is disconnected, the relay will not move. With status indicator: power (green), 1-channel relay status indicator (red). All module size interfaces can be directly connected through the terminal block, which is convenient and practical.
5V 1 Channel SSR G3MB-202P Solid State Relay Module
In stock
A Solid State Relay is similar to a mechanic relay But it is a low-level trigger relay, So the relay will turn on at LOW level input (that is Digital 0 will turn ON the relay). And hence it can be controlled through a digital signal. Solid State Relay generates no noise and has a much longer lifespan in compared to the traditional mechanic relay.
When the input logic voltage is applied to the coil, the NC will disconnect from the COM breaking the conductivity between the two. At the same time, the NO will connect with the COM allowing conductivity between them. Depending on your wiring this will turn on or off the connected load
5V 10A PCB Mount Sugar Cube Relay
In stock
This is a 5V Relay Cube. This cube relay has an operating voltage of 5V and has a max current capacity of 10A. This makes it most suitable for use in microcontroller-based devices.
5V 2 Channel SSR G3MB-202P Solid State Relay Module
In stock
A two-channel relay module (HCMODU0115) featuring 2x Omron G3MB-202P solid state relays. This 5V 2 Channel SSR G3MB-202P Solid State Relay Module is capable of switching AC voltages between 100 and 240V at up to a 2A current. The module can be controlled from a 5V digital source such as an Arduino microcontroller.
A resistive type fuse is provided on the module to help protect excessive current draw.
This 5V 2 Channel SSR G3MB-202P Solid State Relay Module 240V 2A Output with Resistive Fuse is based on the Omron G3MB SSR relay which can control up to 2A at 240VAC. This is a 2 Channel SSR relay module, each relay channel has 3 separate terminals, NO (Normal Open), COM (Common), NC (Normal Closed).
5V 2A 8-Channel SSR G3MB-202P Solid State Relay Module
In stock
This 5V 2A 8-Channel SSR G3MB-202P Solid State Relay Module (Low level Trigger) is based on the G3MB SSR relay which can control up to 2A at 240VAC. This is an 8 Channel SSR relay module, each relay channel has 3 separate terminals, NO (Normal Open), COM (Common), NC (Normal Closed).
A Solid State Relay is similar to a mechanic relay where it can be controlled through a digital signal. Solid State Relay generates no noise and has a much longer lifespan in compared to the traditional mechanic relay.
When the input logic voltage is applied to the coil, the NC will disconnect from the COM breaking the conductivity between the two. At the same time, the NO will connect with the COM allowing conductivity between them. Depending on your wiring this will turn on or off the connected load.
5V 2A Wireless Transmitter Receiver Charging Coil Module
In stock
The 5V 2A wireless transmitter receiver charging coil module is for a variety of small electronic products, wireless charging, power supply development, and design, with a small size, easy to use, high efficiency, and low price characteristics.
It is mainly used in mobile electronics products such as for charging mobile phones and electronics gadgets wirelessly. The adoption of a Contactless charging power supply can be used to sealing of the products to make them waterproof and dustproof and increase product service life to make it more convenient.
5V 3A UBEC
In stock
Features:
- Suitable for: RC AirPlane Multirotor helicopter
- Ideal for high power application requiring currents up to 3A.
- Small size UBEC
- Easy to use.
5V 4 Channel Relay Module
In stock
This is 5V 4-Channel Relay interface board, be able to control various appliances and other equipment with large current. It can be controlled directly by Microcontroller (for Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic). This is 0~2.5V triggered Low Level Trigger 4 Channel Relay Module.
5V 4 Channel SSR G3MB-202P Solid State Relay Module
In stock
This 5V 4 Channel SSR G3MB-202P Solid State Relay Module 240V 2A Output with Resistive Fuse is based on the Omron G3MB SSR relay which can control up to 2A at 240VAC. This is a 4 Channel SSR relay module, each relay channel has 3 separate terminals, NO (Normal Open), COM (Common), NC (Normal Closed).
A Solid State Relay is similar to a mechanic relay where it can be controlled through a digital signal. Solid State Relay generates no noise and has a much longer lifespan in compared to the traditional mechanic relay.
When the input logic voltage is applied to the coil, the NC will disconnect from the COM breaking the conductivity between the two. At the same time, the NO will connect with the COM allowing conductivity between them. Depending on your wiring this will turn on or off the connected load.
5v 5a Buck Module with Usb XY-3606
In stock
Features:
- The synchronous rectification scheme, wide voltage, high current, high efficiency.
- With DC plug and terminals, easy to use.
- With USB port, fast-charge identification chip compatible with Android and iPhone mobile phones.
5V 7A Sugar Cube Relay
In stock
SPDT(Single Pole Double Throw) relay is used as a switch for high current AC/DC appliances which need to be controlled from a microcontroller or sensor output. 5V PCB Mount Sugar Cube SPDT Relay instead of its small size can switch a load of 7A connected to it. The coil resistance of this relay is 70 ohm whereas the coil current is 70mA. The trigger voltage for this relay is 5V. There are 5 pins in this relay i.e, Coil end 1, Coil end 2, COM(common), NC and NO. Coil end 1 and Coil end 2 are used to trigger ON/OFF the relay. One end is connected to a 5V supply and the other is connected to the ground of the circuit. Common is connected to the one end of the load to be controlled. The other end of the load is connected to either NC or NO. If the load is connected to NC(Normally Closed) then the load remains ON before trigger. And if it is connected to NO(Normally Open) then the load remains OFF before trigger. These relays are usually used in home automation, switching circuits, security circuits, etc.
5V 8 Channel Relay Module
In stock
It is a 5V 8 Channel Relay Module. The relay normally open interface maximum load: AC 250V/10A, DC 30V/10A. It has a trigger current of 5mA, and module working voltage of DC 5V. Each channel of the module can be triggered by a jumper to set a high level or a low level. Fault-tolerant design, even if the control line is disconnected, the relay will not move. With status indicator: power (green), 6-channel relay status indicator (red). All module size interfaces can be directly connected through the terminal block, which is convenient and practical.
5v 8 channel Relay Module with Optocoupler
In stock
It is an 8 Channel Isolated 5V 10A Relay Module opto coupler, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc. It is also able to control various appliances and other types of equipment with a large current. Relay output maximum contact is AC250V 10A and DC30V 10A.
One can connect a microcontroller with standard interface directly to it. Red working status indicator lights are conducive to the safe use. The 8 Channel Isolated 5V 10A Relay Module opto coupler has a wide range of applications such as all MCU control, industrial sector, PLC control, smart home control.
5V Dpdt RELAY Telecom Type 2a
In stock
The 5V 2A Telecom Relay has high current capacity. It has contact rating of 2A @ 30V DC. The breakdown voltage between contact and coil is also very high. It requires very less power for operating.
5V Dual Channel Relay Module
In stock
This is a 5V Dual Channel Relay Module with Optocoupler for Arduino PIC ARM. It can be used to control various appliances and other types of equipment with a large current. It can be controlled directly with 3.3V or 5V logic signals from a microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
This 5V Dual Channel Relay Module has a 1×4 (2.54mm pitch) pin header for connecting power (5V and 0V), and for controlling the 2 relays.