Drone Parts

Key Points of Mixed Control Debugging:

l First make sure the forward and backward motors are in the same direction. (If a motor is turning incorrectly, exchange the +-stage wires behind the motor)

l Then adjust the direction, if it is not as expected, the remote control may be reversed, set it back

The Dual-mix ESC Has the Following Modes: 

l Mixed control mode (both throttle / steering mode): 2 or 3 channels (2 channels are recommended because 2 channels automatically return to center) to control the throttle, 1 channel (or 4 channels) to control speed difference steering, throttle ratio 100%, steering ratio 100%, steering priority. Suitable for: tank (in this mode, gun control can play tanks), 4-wheel drive trolley (apm can be installed)

l Two-way independent: it is equivalent to two independent ESCs (if you want to simulate a real tank, the white three wires on the input end are connected to the receiver throttle (3 channels), and the yellow single wire is connected to the receiver 2 channels)

l Two-way synchronization: In mixed control mode, do not connect a single yellow wire, so that the two-way motor output is consistent

This 20A Brushed Electronic Speed Controller is a small-sized ESC that can supply a current up to 20A by using a 2S lipo battery as an input. The ESC accepts a standard RC signal as input and offers functions as forward, reverse, and breaking. This ESC has high-quality silicone cables for the battery input and the motor output.

3-pin extension cable cord, female to male lead wire for servo extension connection control board remote control parts Female to male connectors: These servo connector wires have female connector on one side and male connector on the other side, can be connected to the receiving set and steering engine. 3-Pin extension cable: The servo extension lead wires featured with 3 pins, and each has an angle, in case you will install incorrectly, convenient use design. Application: The servo extension wire kit can be applied for Futaba and JR style servo, remote control car, RC Car, plane and helicopter servo connection or receiver connection.

This is a 2312 920KV Brushless DC Motor for Drone (CCW Motor Rotation).

If you are wandering to build a drone and don’t know what will be the best motor for you then worry no more, we have got your back. we have everything for you to get started with your drone project.

This is our medium-priced high-quality Brushless DC Motors for Drone or Quadcopters.

The CNC Machined Aluminium case makes them more attractive in look than those traditional black-colored Brushless Motors for Drone.

This motor is compatible with 2-4s Li-ion batteries and 30 A Esc also it has  Well-balanced good quality magnets give you a smooth running experience. This premium quality 2312 920KV Brushless DC Motor for Drone is good to go for many UAV pilots.

• FEATURES :

1. Signal System: PAL
2. Auto Gain Control(AGC)
3. Backlight compensation(BLC)
4. WDR D-WDR
5. DNR 2DNR
6. Day/Night Auto/Color/B*W
7. Electronic Shutter Speed PAL: 1/50-100.000

Standard BLDC 30 amp ESC Electronic Speed Controller with Connector is specifically made for quadcopters and multi-rotors. It provides faster and better motor speed control giving better flight performance compared to other available ESCs.

STANDARD 30 amp ESC Electronic Speed Controller can drive motors that consume up to 30A current. It works on 2-3S LiPo batteries. The onboard BEC provides regulated 5V(2A max draw) to power the flight controller and other onboard modules.

30A BLDC ESC Electronic Speed Controller is specifically made for quadcopters and multi-rotors. Which provides faster and better motor speed control giving better flight performance compared to other available ESCs.

Simonk 30A BLDC ESC Electronic Speed Controller can drive motors that consume current up to 30A. It works on 2-3S LiPo batteries. This electronic speed controller offers a battery eliminator circuit (BEC) that provides 5V and 2A to the receiver so we don’t need an extra receiver battery.

This version of the ESC also includes backward-polarity protection and protection on the 5V receiver line, this means that if you accidentally attach a battery backward it won’t destroy your motor controller and other BEC won’t affect the ESC.

30CM 22AWG Servo Lead Extention (Futaba) Cable is stronger & allows more current than standard servo wires. Great for larger planes with servos that experience high loads. These cables are available in various sizes for making connections such as between RC servo controllers or RC receivers and motor controllers with an RC interface. These Servo Lead Extention comes with “FUTABA”-style connectors. This has a male connector on one side and one female connector on another side. These High-Quality silicon cables are soldered and crimped male-female plugs at both ends. A high-quality secure servo connection, every time.
It can also be a convenient way to connect various 3-pin sensors to a robot controller.

The 3DR Radio Telemetry 433Mhz 1000MW with 2~3km Data Telemetry has an independent signal amplifier (1W). Both modems here have the same design and can be used both in the ground station and in the air, and each also has a Micro USB TTL connector. The small omnidirectional antenna has a range of several kilometers, with a bidirectional amplifier a longer range is achievable. This product is based on HM-TRP radio modules with Si1000 8051 microcontrollers.

The TS832 Transmitter packs a whopping 600mW of ultra clean 5.8GHz power! A must for those looking for longer range and locked in video. The TS832 is transmitting a full range of 32 channels and uses an easy to use 2 button interface, it also comes with a clean pre-wired harness, and only weighs in at a scant 21grams, it’s Perfect for a wide range of aircraft!

The 40Kg-cm Servo Motor (S8218) is a well-designed and high-quality servo that is digital, and fitted with metal gears for reliability. This is a digital servo motor for a wide range of applications that requires high torque. You can control this servo motor with Arduino which is connect by jumper wires and powered by battery.

The metal gears ensure long life and torque conversion. It is made of high-quality material, which may make your operation much more remarkable. This product is a metal gear high torque servo motor.

This is 433Mhz 100mW Radio Telemetry V2 Kit is based on the 3DR Telemetry kit and is 100% compatible as it runs the same firmware onboard. This firmware used by 3D Robotics is completely open-source which is, of course, the reason we are able to use it on our own version at Unmanned Tech.

The Unmanned Telemetry Kit is compatible with Ardupilot or Pixhawk-based systems and allows you to easily add a two-way telemetry connection between your drone and ground station. This product comes with our full support and warranty as we are confident in the functionality and reliability of this item.

This is the new and improved V2 of the Unmanned Telemetry kit. The full features and specifications are listed below but the main features are that both air and ground module are now interchangeable, and each is with a USB connector and a DF13 connector. Please note that to connect to Pixhawk, it is a good idea to also purchase a 6-pos to 6-pos cable as this is easier and better than using the cable included.

5.8G UVC OTG Android Phone Receiver is a new receiver that you can connect to your smartphone directly instead of a heavy monitor and is good for those who feel dizzy when wearing FPV goggles.

It has low latency of around 100ms 150CH auto search allows covering all 5.8G frequency bands.

The 5MP Raspberry Pi 3/4 Model B Camera Module Rev 1.3 with Cable equips flexible cable for attaching with Raspberry Pi 3 Model B. The 5MP camera module is perfect for small Raspberry Pi projects which have very little space allowance just boot up the latest version of Raspbian and you are good to go!!!

The high-definition 5MP camera delivers outstanding photos but can also shoot video, ideal for drones or CCTV projects. The lightweight camera board allows for it is useful in more practical roles, such as a hidden camera, or even a camera for a Pi phone.

Features:

1. Suitable for: RC AirPlane Multirotor helicopter
2. Ideal for high power application requiring currents up to 3A.
3. Small size UBEC
4. Easy to use.

Features:

1. Type: Voltage Regulator
2. Speed range: from 0% to 100%
3. Phase inversion Control: Yes
4. Voltage polarity protection: Yes
5. Overcurrent Protection: Yes.
6. Suitable for hard brushless motor, brushless motor drive and other miniature 3 / 4 wire brushless motor without hall